2006 Ford Expedition/ Ford Navigator Workshop Manual Pinpoint Test C: The...
download The vehicle security module monitors the door ajar and remote keyless entry (RKE) status. Based on the door ajar status (doors, liftgate, and liftgate glass), the instrument cluster then...
View Article2002 Ford F 250 2WD Super Duty Ford 10.5 Inch Full-Floating Rear Drive Axle...
download Axle Shaft Removal 1. NOTE: The wheels and tires do not have to be removed in order to remove the axle shafts. Loosen and remove the retaining bolts. 2. Remove the axle shaft. 3. Inspect the...
View ArticleSingle-Nozzle Nitrous Kit 2001 Ford Escape,1999 Ford Ranger, Explorer & Sport...
NITROUS DELIVERY SYSTEMThe nitrous-oxide cylinder should be mounted in the cargo area, bed, or similar area, but not in the driver’s compartment. The positioning of the cylinder must be executed as...
View ArticleFORD FIESTA – HIGH RPM PROBLEM
download Fault Idle would intermittently rev up to 4000 rpm. Car would also accelerate on its own up to around 3000 rpm when driven off. If clutch depressed during this time while driving, the engine...
View Article1998 Ford Windstar Camshaft Position (CMP) Sensor REMOVAL AND INSTALLATION
download CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126) , set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the...
View Article1994 Ford Pickup F150 BALL JOINT Removal Installation
download NOTE: Always remove lower ball joint before removing upper ball joint. Install lower ball joint before installing upper ball joint. DO NOT heat ball joint or axle to aid in installation....
View Article2002 Ford Windstar Camshaft Synchronizer REMOVAL AND INSTALLATION
download Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01. 2. Drain the cooling system. For additional information, refer to Section 303-03. 3. Remove...
View Article1995 Ford Mustang Camshaft Position (CMP) Sensor Removal Installation
download 1. Disconnect battery ground cable (14301) . 2. Disconnect fuel charging wiring (9D930) from distributor stator (12A112) (camshaft position sensor). 3. Remove stator camshaft position sensor...
View Article2005 Ford Expedition, Ford F-250, Ford F-350 TICKING AND/OR KNOCKING NOISE...
download FORD: 2005 Mustang 2004-2005 F-150 2005 Expedition, F-250, F-350 This article supersedes TSB 05-15-8 to update the Service Procedure. ISSUE Some vehicles equipped with a 4.6L 3-valve or 5.4L...
View ArticleFord / Mercury / Lincoln Band-Mounted Sensor Re-Learn Instructions
The instructions below can be used for the following vehicles: 2008 Ford Crown Victoria / Lincoln Town Car / Mercury Grand Marquis 2008 Ford E-series 2007-2009 Ford Edge / Lincoln MKX 2005-2008 Ford...
View Article1996 Ford Aerostar/Ranger/Explorer Camshaft Position (CMP) Sensor REMOVAL AND...
download CAUTION: Syncro Positioning Tool T95T-12200-A (3.0L, 4.0L) or T96T-12200-A (5.0L) must be obtained prior to installation of the replacement synchronizer assembly. Failure to follow this...
View Article2002 Ford Taurus Camshaft Synchronizer REMOVAL AND INSTALLATION
download Removal 1. CAUTION: The No. 1 cylinder must be set on top dead center (TDC) of the compression stroke or the synchronizer assembly will not be installed correctly. CAUTION: Do not turn the...
View Article2004 Ford Freestar Intake Manifold Runner Control (IMRC) Actuator Removal and...
download Removal and Installation 1. Disconnect the battery ground cable. For additional information, refer to Section 414-00. 2. Remove the parts in the order indicated in the following illustration...
View Article